Duran®

Ward Leonora — Thu, 05 Mar 2026 10:18:29 +0000

Duran® SCHEU-DENTAL is a hard-elastic transparent material, bonds to acrylic. No pre-drying required.

Applications – occlusal splints and retainers.

For best results use with Isofolan spacer foil.

Ministar_Biostar_Application_manual.pdf (eurodontic.co.uk)

Intended purpose: Thermoplastic foils for the
manufacture of appliances and splints for dental
and orthodontic treatments.
Indication: Suitable only for the fabrication of
dental splints in different areas of application
such as aligner splints, retention splints, bite
splints and mandibular protrusion splints.
Indication table with further indications and
instructions for use at www.scheu-dental.com/
pressure-moulding-material.
Contraindication: Allergic reactions to compo- nents of DURAN®/DURAN®+ (PETG) cannot be
ruled out in sensitised people.
Any use not stated above is contraindicated.
Storage: Store at 5°C to 35°C. Protect from
sunlight. Keep dry.
Important: Must only be used by qualified per- sonnel. For single use. Not suitable for partial
build-up with light-curing resins. Any serious
incident involving the product must be reported to
the manufacturer and the competent authority
immediately.
Safety information: The practitioner is responsible for correct use. The splint must not be used if
the material is cracked/broken/contains bubbles;
there is a risk of swallowing or aspiration. When
using DURAN® with 3D-printed models, a
non-perforated protective foil (ISOFOLAN®) or
alternatively DURAN®+ must be used. Remove
the protective foil after the thermoforming pro- cess. Do not bring the products into contact with
alcohol-based/organic solvents, hot water or
steam jets.

https://www.scheu-dental.com/en

The post Duran® appeared first on Eurodontic.

Duran® + 125mm rd (with insulation foil attached)

adm1n-fcdm — Fri, 09 Jan 2026 13:33:08 +0000

Duran® + SCHEU-DENTAL is a hard-elastic transparent material, bonds to acrylic. No pre-drying required. With integrated insulation foil.

Applications – occlusal splints and retainers.

https://schttps://www.eurodontic.co.uk/product-category/pressure-moulding/materials-accessories/

https://scheu-dental.com/en

Ministar_Biostar_Application_manual.pdf (eurodontic.co.uk)

DURAN+_Instructions

Datasheet-DURAN_plus

Description: DURAN®+ is a clear-transparent, tough and abrasion-resistant PET-G thermoforming material with outstanding properties in terms of breaking strength, elasticity and dimensional stability. DURAN®+ belongs to the family of polyester resins, combining extremely low water absorption and highest biocompatibility (it does not require pre-drying).
The material has been tested and approved in terms of cell biology.
Indication: is ideally suited for all indications in prosthetic and orthodontic splint therapy, such as Miniplast splints,
occlusal splints with and without adjustments, CMD splints, retention splints, Essix retainer and palatal expansion.
As hard-elastic splint material, DURAN®+ is predestined for tooth transpositions, fine corrections and retentions in
splint therapy.

Pessure moulding: Full models should be embedded in the pellets and dental arcade models should be placed on the model platform.
As you can see from the imprint directly on the material or on the packaging labels, the heating times for DURAN®+ are
extremely short. The initial thickness of DURAN®+ will be reduced slightly depending on the model height. Make sure
to remove the integrated protection foil after taking off the splint from the model and prior to inserting it.
Finishing: Up to a thickness of 1.0 mm, DURAN®+ can be easily trimmed with SD-Foil scissors A (REF 3460). For thicknesses exceeding 1.0 mm, we recommend using the finishing set (REF 3378). Final trimming and polishing can be most effectively done with DIMO / DIMO® PRO discs (REF 3380-3384/3376). Compound and adjustment with cold cure resins such as
DURASPLINT® are possible without any problems. For most C+B and/or temporary materials – especially bis-acrylic
composites – the use of a bonding agent is recommended. Make sure to check the suitability of the corresponding
bonding agent prior to using it.
Cleaning/care: Products from the CETRON® range are the best choice for daily cleaning and care. Detergents or products on the base
of alcohol or plants (e.g. Pyralvex®) as well as hot water or steam jets should not be used.
Note: Heating times of less than 20 seconds can not be coded in BIOSTAR® devices. In these cases, the heating time must
be entered manually using the key with the „clock symbol“.
Storage: Protect from sunlight. Store in a dry place.

The post Duran® + 125mm rd (with insulation foil attached) appeared first on Eurodontic.

0.5 mm hard Archives — Eurodontic

Duran®

For best results use with Isofolan spacer foil.

Duran® + 125mm rd (with insulation foil attached)