Duran®

Ward Leonora — Thu, 05 Mar 2026 10:18:29 +0000

Duran® SCHEU-DENTAL is a hard-elastic transparent material, bonds to acrylic. No pre-drying required.

Applications – occlusal splints and retainers.

For best results use with Isofolan spacer foil.

Ministar_Biostar_Application_manual.pdf (eurodontic.co.uk)

Intended purpose: Thermoplastic foils for the
manufacture of appliances and splints for dental
and orthodontic treatments.
Indication: Suitable only for the fabrication of
dental splints in different areas of application
such as aligner splints, retention splints, bite
splints and mandibular protrusion splints.
Indication table with further indications and
instructions for use at www.scheu-dental.com/
pressure-moulding-material.
Contraindication: Allergic reactions to compo- nents of DURAN®/DURAN®+ (PETG) cannot be
ruled out in sensitised people.
Any use not stated above is contraindicated.
Storage: Store at 5°C to 35°C. Protect from
sunlight. Keep dry.
Important: Must only be used by qualified per- sonnel. For single use. Not suitable for partial
build-up with light-curing resins. Any serious
incident involving the product must be reported to
the manufacturer and the competent authority
immediately.
Safety information: The practitioner is responsible for correct use. The splint must not be used if
the material is cracked/broken/contains bubbles;
there is a risk of swallowing or aspiration. When
using DURAN® with 3D-printed models, a
non-perforated protective foil (ISOFOLAN®) or
alternatively DURAN®+ must be used. Remove
the protective foil after the thermoforming pro- cess. Do not bring the products into contact with
alcohol-based/organic solvents, hot water or
steam jets.

https://www.scheu-dental.com/en

The post Duran® appeared first on Eurodontic.

Bioplast®

Ward Leonora — Sun, 09 Jun 2024 09:25:33 +0000

Bioplast by SCHEU-DENTAL is a Soft, pliable, rubber-like, transparent material. Does not bond to acrylic.

Applications – mouthguards, bruxism splints, (bleaching trays 2 mm or more- recommend Bioplast Bleach product code 3190 if you require 1mm which is firmer than Bioplast 1 mm)

Description: BIOPLAST® is a soft elastic rubber-like thermoforming material made of ethylene vinyl acetate (EVA) that does not bond
to acrylic. BIOPLAST® has been tested and approved for its biological safety.

Indication: Duplicating moulds for plaster situation models, mouth guard, bruxism splints, positioner, OSAMU-Retainer®.

Model Preparation: If necessary, block out strong undercuts using BLUE-BLOKKER® before pressurizing. For model insulation we recommend BIOPLAST® insulating agent (REF 3189/3166). Apply one layer of the insulating agent to the model, making sure
to prevent the liquid from accumulating in the cavities as well as from drying out.

Pressure Moulding: We recommend to place dental arcade models on the model platform and to embed full models in the pellets. Adhesion
of pellets to the model and the resulting loss of pellets can be considerably reduced by using the pellet cover (REF 3006
large/REF 3007 small).

Finishing: You can reduce the splint to its final extension using SD foil scissors A (REF 3460) or B (REF 3461). The BIOPERM
trimmer (REF 3226), DIMO®PRO (REF 3381), DIMO®PRO SLIM (REF 3376) and POLYFIX (REF 3371) are best suited for
finishing. Best polishing results are achieved using the OSAMU polisher (REF 3247) at 5000 – 10000 rpm.

Cleansing/care: Our CETRON® cleansing and care products are the best choice for splints made of BIOPLAST®.

Storage: Protect from sunlight. Store in a dry place.

Safety note: To be used only for the above indication and by qualified personnel. For single use. Serious incidents in connection with the
use of the product must be reported immediately to the manufacturer and the competent authority!

BIOPLAST_VKP_0373_GB_Original_3288

https://scheu-dental.com/en

The post Bioplast® appeared first on Eurodontic.

3 mm blank Archives — Eurodontic

Duran®

For best results use with Isofolan spacer foil.

Bioplast®